Go to the main screen. Press the Down Arrow in the Navigation Group. The Spot target line weight increases and the red cursor under Menu dims slightly.
Use the directional arrows to move the Spot target to the desired location. Page 2. Select Rack from the Mode drop-down menu. Spot is automatically selected from the Zone drop-down menu, since rack focus only works with Spot zone. The focus distance displays for each rack point. To reset the focus distance to the value calculated by the autofocus algorithm, select Re-Autofocus. Page When the AE feature is able to match the sensor brightness, the overlay turns yellow.
If the brightness fluctuates more than half of a stop, the overlay turns red. Page Channel Modes Use the limiter in dynamic environments where external mixers are not practical for controlling signal strength. The limiter is only available with analog audio input. Assign each audio channel to the Left, Middle, or Right side of the stereo mix.
Move the sliders up and down to adjust the volume. In a digital system, dBu is an approximation; the correct unit for digital audio levels is dBFS. Page Chapter 7: Redmote Operation 50 ft. The default channel is 0. Page Shutdown menu. Press Button 1. Wireless communication is at risk of being lost when the battery indicator is red. Uncompress and open the zip file. Open the Win folder. Edge timecode default begins at , but can be configured in the Media menu.
Page 4. Page Genlock Monitor Sync is achieved automatically when a genlock signal is provided that is compatible with the current monitor output frequency. On the Slave camera s , follow the instructions below: A. Page 5. On both cameras, select Format Connect the Ethernet connector to the router. Page The diagram below is an example of how to set up a camera array. Set Genlock Source to Brain. Page Supply a pulse from the Motion Control device to sync the shutter to the rising edge of the sync input.
Additional timecode devices may be compatible, but have not yet been tested by RED. Page Chapter 9: Upgrade Dsmc Firmware 1. If you have user-generated preset files on your camera, follow the instructions below to save the files to an SSD: A. Page C. As with all optical glass, any type of physical contact with the OLPF may scratch or damage the surface.
Page Lcd And Evf Screens Hand wash and air-dry the RED Microfiber bag regularly. Page A. A Hard Restore functions like a System Restore in that it changes all settings to the factory default values. Page You want to work with. R3D files but your footage is in another file format. R3D is the native recording format of RED cameras. It is not possible to convert another file format into the.
R3D format. Page Appendix A: Technical Specifications NOTE: When connecting a cable to a connector, align the key and red marker on the cable connector with the corresponding key and marker on the device connection.
Page Hd-Sdi Out If you have a drop frame project time base such as Page Hdmi Out 2. The HDMI output is progressive scan p ; it does not support progressive segmented frame PsF or interlaced i scan formats. For maximum quality, use high impedance headphones. Use standard values. By integrating a global shutter, temporal anti-aliasing soft shutter, and variable neutral density ND system into a single lens mount, the MOTION MOUNT delivers on-the-fly shutter adjustments to reduce motion blur and temporal aliasing.
However, RED recommends that you change lens mounts only in dust-free environment. For information about the compatibility of Remove the rear lens cap. Page Setup Press the camera key you want to change. Page This menu allows the user to reset the battery backed up internal clock of the camera.
This time value is used as a timestamp on the. NOTE: Enter time in hour clock format. Default is NONE. Page Permits the user to adjust the Subnet Mask the property on other cameras.
SET commands address. Gateway Permits the user to adjust the Gateway address. Page REDLink wireless connection in the event of interference from other wireless devices. Auto unchecked will pick the "cleanest" channel automatically on each camera boot. Manual Channel Select is the default setting and for default uses Channel 0. Page Sets a fixed fan speed to be used during Record.
Standby Speed Sets a fixed fan speed to be used during Standby. After capture, upload the. They are made to protect the lens, not necessarily to block light This can be used to generate a calibration for long exposures.
After calibration Which takes about 10 min , the new map is automatically selected. Page 3. Select OK to perform the Black Shading calibration. The calibration will make 2 passes. A status screen will show progress of the Capturing step. Second pass shown. Once Capturing is complete, a status screen will show progress of the Analyzing step. Page 8. The camera will perform this procedure twice.
Select OK to complete Black Shading calibration. Page Place your finger on the touchscreen and hold it there until the main screen appears. Page When selected, you will be asked to confirm if you want to reset all hardware discovery settings. Allows you to change the ISO in the clip during playback. Page Opens the advanced White Balance settings without the ability to Calculate.
VIEW Allows you to select the items to be displayed in the playback window. Load will highlight. Select LOAD to load the clip in the player and allow playback. Record Exit When selected will exit playback to the main menu. Page Directional Pad: Pressing Left or Right to open and allow playback of the previous or next clip on the media. Page Displays the clip histogram. The histogram will change based on any changes made in the Upper Controls. Page Helps when the clip is rather long and you want to focus on a particular segment.
You can use the navigation group to select the exact location of the In and Out Points if desired. A higher number reflects a later release.
This reserves a small amount of capacity for ancillary data to be written to the media. Page Using Side Handle. RDM folder on the digital magazine to the archive storage media. This copies all the media and metadata files. You will not need to copy the log, magazine profile, or presets files, but if you do so, it will do no harm. Page Erasing Media Erasing of the media must be performed by formatting on the camera.
Open the Disk Utility. Carefully choose the drive from the list on the left. When used as a Tally, the rising edge of the pulse indicates start of record, falling edge represents end of record. Due to the requirement for absolute data integrity this requires a custom cable manufactured by RED, the pin-out of this interface is not published.
Make sure these contacts are kept clean and free of any contaminants that may interfere with a reliable electrical contact. Note: In Version 3. The upper LED is used to signal camera readiness and camera record status. Page Below the Navigation Group is the focus and record button. NOTE: Wireless mode shown. To stop recording, press the REC button a second time.
Page Operation: Redmote Menus 3. Page Note: Once this procedure has occurred once, the REDMOTE will automatically search for the camera each time it is undocked, until the paired camera selection is changed.
Use the directional arrows on the Navigational Control to move the Red cursor to the desired location within that page to place the parameter. Page 9. These buttons select between a variety of camera status page layouts. Page Maintenance Yellow. When battery charge is critically low, and wireless communication is at risk of being lost the icon turns Red. Page USB based power source such as laptop P. Page Upgrading Redmote Firmware 4. In the IP Address field, enter In the Subnet Mask field, enter The file will unzip automatically when downloaded.
If not, enter it again as outlined in the procedure. Click "Select File" and navigate to the redmote. Page File transfer status will be displayed as a Blue bar. Uncompress the zip file. Open the newly created folder. Page 5. Choose the location for the shortcut. NOTE: Only one file can be added for upgrade.
Page Slave Camera "left eye" and "right eye" camera in the stereo pair. Page Connecting Cameras 2. For example, ask someone to swing their arm. What you would observe in a traditional recording of this action is constant motion blur until the arm stops. However, what your eye sees is both motion blur and a sharper reference of the arm throughout the motion path.
All Files. You are here:. Read Before You Shoot Read this operation guide carefully and in its entirety before assembling or operating your camera or other RED accessories.
Shoot For Video and Stills High resolution video, such as the digital footage captured by the camera, has surpassed the detail necessary to produce professional full-sized prints. Adobe Photoshop : Can open. R3D files. Vegas Pro.
0コメント